go-v.orgdoi

Bathymetry and capacity of Shawnee Reservoir, Oklahoma, 2016

Chad E. Ashworth, S. Jerrod Smith, Kevin A. Smith · Scientific investigations map · 2017

  • DOI 10.3133/sim3374
  • Publisher United States Geological Survey
  • Type report
  • Issued 2017

Not cached yet. This record was fetched live for this request and is stored after the lookup. Reopening the page should serve the cached copy.

Scientific investigations map · United States Geological Survey · report · 2017

Abstract

Shawnee Reservoir (locally known as Shawnee Twin Lakes) is a man-made reservoir on South Deer Creek with a drainage area of 32.7 square miles (U.S.

Geological Survey, 2016a) in Pottawatomie County, Oklahoma (fig.1).The reservoir consists of two lakes connected by an equilibrium channel.The southern lake (Shawnee City Lake Number 1) was impounded in 1935, and the northern lake (Shawnee City Lake Number 2) was impounded in 1960.Shawnee Reservoir serves as a municipal water supply, and water is transferred about 9 miles by gravity to a water treatment plant in Shawnee, Oklahoma.Secondary uses of the reservoir are for recreation, fish and wildlife habitat, and flood control.Shawnee Reservoir has a normal-pool elevation of 1,069.0feet (ft) above North American Vertical Datum of 1988 (NAVD 88) (Steve Nelms, City of Shawnee, written commun., 2016).The auxiliary spillway, which defines the flood-pool elevation, is at an elevation of 1,075.0ft.The U.S.

Geological Survey (USGS), in cooperation with the City of Shawnee, has operated a real-time stage (water-surface elevation) gage (USGS station 07241600) at Shawnee Reservoir since 2006 (U.S. Geological Survey, 2016a).For the period of record ending in 2016, this gage recorded a maximum stage of 1,078.1 ft on May 24, 2015, and a minimum stage of 1,059.1 ft on April 10-11, 2007 (U.S.

Geological Survey, 2016a).This gage did not report reservoir storage prior to this report (2016) because a sufficiently detailed and thoroughly documented bathymetric (reservoir-bottom elevation) survey and corresponding stage-storage relation had not been published.A 2011 bathymetric survey with contours delineated at 5-foot intervals was published in Oklahoma Water Resources Board (2016), but that publication did not include a stage-storage relation table.The USGS, in cooperation with the City of Shawnee, performed a bathymetric survey of Shawnee Reservoir in 2016 and released the bathymetric-survey data in 2017 (Smith and others, 2017).The purposes of the bathymetric survey were to (1) develop a detailed bathymetric map of the reservoir and (2) determine the relations between stage and reservoir storage capacity and between stage and reservoir surface area.The bathymetric map may serve as a baseline to which temporal changes in storage capacity, due to sedimentation and other factors, can be compared.The stage-storage relation may be used in the reporting of real-time Shawnee Reservoir storage capacity at USGS station 07241600 to support water-resource management decisions by the City of Shawnee.

MethodsRaw bathymetric-survey data (water-depth and position measurements) were collected by using methods described by Wilson and Richards (2006) and Mueller and others (2013).These data were collected for the area where land-surface elevations are generally below 1,072 ft and on selected fairweather days during the study period of June 21-September 7, 2016.The commercial hydrographic software HYPACK (HYPACK, Inc., 2016) was used to create transect lines to be followed during the survey.Bathymetric-survey data were collected along primary transects aligned parallel to the dam and separated by 100 ft, which is approximately 1 percent of the longitudinal length of each of the lakes.Control transects were aligned at 45 degrees from the primary transects and separated by 500 ft.Additional transects were added as needed to increase data resolution in areas with important lake-bottom features (such as submerged roads) or steep lake-bottom slopes (such as the upstream face of the dam).Most water-depth measurements were made from a flat-bottom boat by using an Odom Hydrographic Systems Echotrac CV100 single-beam echo sounder with a dual frequency 200-kilohertz transducer (Odom Hydrographic Systems, Inc., 2008).Supplemental water-depth measurements were collected by using a kayak-towed Teledyne RD Instruments RiverRay acoustic Doppler current profiler (ADCP; Teledyne RD Instruments, 2016) in Shawnee City Lake Number 2 west of Walker Road (NS 331, fig.

1) because that area (see area enclosed by 1,072 contour in fig.

1) was inaccessible by the flat-bottom boat.Smaller isolated areas on both lakes could not be surveyed by ADCP because they were too remote or too shallow to be accessible by kayak.The area surveyed by ADCP was about 1.6 percent of the total area surveyed by flat-bottom boat and kayak.Water-depth measurements were converted to NAVD 88 bathymetric-survey elevation data during post-processing.Water-depth measurements were subtracted from a daily mean water-surface elevation at USGS station 07241600 located on the intake tower of Shawnee City Lake Number 1.The daily mean water-surface elevation, which was assumed to be constant for all areas of Shawnee Reservoir, was calculated from beginning-of-day and end-ofday manual staff-plate measurements.These measurements never differed by more than 0.03 ft on any day, though the measurements ranged from about 1,074.3 to 1,075.4 ft during the study period.The station datum (NAVD 88) was established by using static global navigation satellite systems (GNSS) techniques (Rydlund and Densmore, 2012) over two control points, reference mark 1 (RM1) and reference mark 3 (RM3) (fig.1).RM1 is a chiseled square on the eastern wing wall of the auxiliary spillway, 15 ft north of the centerline of Belcher Road; RM3 is a stainless-steel concrete anchor bolt with a stainless-steel washer stamped "USGS Survey Marker" on the western wing wall of the auxiliary spillway, 15 ft south of the centerline of Belcher Road (fig.1).Each control point had a minimum 4-hour static GNSS occupation which was processed by using the National Geodetic Survey Online Positioning User Service (OPUS; National Geodetic Survey, 2016), resulting in time-weighted average elevations of 1,085.82ft (RM1) and 1,085.62ft (RM3).The estimated uncertainty of these static observations was 0.03 ft on the basis of a differential level survey between the independent points.Differential levels were also run from RM1 to the staff plate located on the intake tower and the USGS standard wire-weight gage mounted to the handrail of the intake tower to ensure that both were reading correctly in gage datum (NAVD 88).During the bathymetric survey, position was measured by using a differentially corrected Global Positioning System (DGPS) mounted directly above the single-beam echo sounder and ADCP.The positional accuracy of the DGPS data collected at 2 hertz was 1.97 ft 95 percent of the time (Hemisphere GNNS, Inc., 2013).The hydrographic software utilized the time provided by the DGPS to synchronize data from the echo sounder or ADCP and eliminate system latency.Bathymetric-survey data were compiled in a geographic information system (GIS) by using Esri ArcGIS 10.3.1 software and processed by using methods described by Wilson and Richards (2006).Breaklines were generated to reinforce linear features such as submerged stream channels and roads.Contours generated from lidar-derived land-surface elevation data (U.S.

Geological Survey, 2016c) were used to extend the bathymetric survey to cover areas inundated only during floods.Bathymetric-survey data, breaklines, and lidar-derived land-surface contours were combined and modeled as a tri- angulated irregular network (TIN) by using the "Create TIN" tool (Esri, Inc., 2016a). The TIN was converted to a 4-ft-resolution digital elevation model (DEM) by using the "TIN To Raster" tool (Esri, Inc., 2016b). Bathymetric contours at 1-ft intervals (fig.

1) were derived from the DEM by using the "Contour" tool (Esri, Inc., 2016c) and smoothed for cartographic representation at a 1:10,000 scale by using the "Smooth Line" tool (Esri, Inc., 2016d). The bathymetric contours with values between 1,072 and 1,080 ft were generated primarily from lidar-derived land-surface elevation data (U.S. Geological Survey, 2016c), and contours with values less than 1,072 ft were generated primarily from bathymetric-survey data. A stage-storage and stage-area data table (table 1) was derived from the DEM for 1-ft stage increments by using the "Surface Volume" tool (Esri, Inc., 2016e).

The stage-storage and stage- area relations are graphically represented in figure 2A and figure 2B, respectively, by using data from table 1.

Open the resolved locator · 10.3133/sim3374

Metadata licence: OpenAlex metadata (CC0)

Registry
OpenAlex DOI index + API
Fetched
2026-11-19 21:04 UTC
Cache state
not cached yet (bulk-index+openalex)
Locator
https://pubs.usgs.gov/publication/sim3374
Metadata licence
OpenAlex metadata (CC0)
Scope
Metadata as returned by the resolver; abstracts are never generated here.